Safety and Compliance Information
IMPORTANT PRODUCT AND SAFETY INFORMATION
READ ALL SAFETY INFORMATION BEFORE USING THE DEVICE. FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE.
Maintaining Your Device
Do not expose your Device or adaptor to liquids. If your Device or adaptor gets wet, carefully unplug all cables without getting your hands wet and wait for the Device and adaptor to dry completely before plugging them in again. Do not attempt to dry your Device or adaptor with an external heat source, such as a microwave oven or a hair dryer. If the Device or adaptor appear damaged, discontinue use immediately. Use only accessories supplied with the Device to power your Device. To avoid risk of electric shock, do not touch your Device or any wires connected to your Device during a lightning storm.
Only handle your Device with clean hands. Clean the Device with a soft cloth that is slightly damp with water and a touch of rubbing alcohol; be careful not to wipe it with anything abrasive or to use any harsh chemicals. Don't expose your Device to steam, extreme heat or cold. For example, do not install your Device near any heat sources such as space heaters, heater vents, radiators, stoves, or other things that produce heat. Use your Device in a location where temperatures remain within the Device’s operating temperature range set forth on this page.
Use of third-party accessories may impact your Device’s performance. In limited circumstances, use of third-party accessories may void your Device’s limited warranty. Read all safety instructions for any accessories before using with your Device.
Only use the included power adaptor with your Device. Do not force the power adaptor into a power outlet. If the power adaptor or cable appears damaged, discontinue use immediately. Do not plug multiple electric devices into the same wall socket. Overloading a socket can cause it to overheat and may result in a fire.
Your Device may get warm during normal use. To reduce the effect of the warming, place your Device on a heat resistant surface.
Other Safety Considerations
Small parts contained in your Device and its accessories may present a choking hazard to small children.
For safety, compliance and other information regarding any networking equipment or computer connected to your Device, please consult the user manual and other information provided by the manufacturer.
Install your power adaptor into an easily accessible socket-outlet located near the equipment that will be plugged into, or powered by, the adaptor.
To avoid risk of electric shock, do not touch your Device or any wires connected to your Device during a lightning storm.
Do not expose adaptor or cable to liquids.
Using Your Device Around Other Electronic Devices
Your Device generates, uses, and can radiate radio frequency (RF) energy and, if not used in accordance with its instructions, may cause interference to radio communications and electronic equipment. External RF signals may affect improperly installed or inadequately shielded electronic operating systems, entertainment systems, and personal medical devices. While most modern electronic equipment is shielded from external RF signals, if in doubt, check with the manufacturer. For personal medical devices (such as pacemakers and hearing aids), consult with your physician or the manufacturer to determine if they are adequately shielded from external RF signals.
Recycling Your Device Properly
In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of, or recycle your Device in accordance with your local laws and regulations. For information about recycling your Device, go to amazon.com/devicesupport
Servicing Your Device
If your Device needs to be serviced, please contact eero Customer Support. Contact details can be found at https://support.eero.com
Faulty service may void the warranty.
Innovation, Science and Economic Development Canada (ISED) Compliance
This Device contains licence–exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence–exempt RSS(s). Operation is subject to the following two conditions: (1) This Device may not cause interference. (2) This Device must accept any interference, including interference that may cause undesired operation of the Device.
Information Regarding Exposure to Radio Frequency Energy
This equipment complies with IC RSS-102 RF exposure limits set forth for an uncontrolled environment.
This Device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. This equipment should be installed and operated with a minimum distance of 22 cm between the radiator and your body.
(1) Operation shall be limited to indoor use only; and
(2) Operation on oil platforms, cars, trains, boats and aircraft shall be prohibited except for on large aircraft flying above 10,000 ft.
CAN ICES-3 (B)/NMB-3(B)
Product Specifications
eero
Device name: eero
Model: J010001
Wi-Fi connectivity
Dual-band Wi-Fi radios, simultaneous 2.4 GHz and 5 GHz, 2x2 MU-MIMO, beamforming, IEEE 802.11a/b/g/n/ac
Wired connectivity
Two auto-sensing gigabit ports for WAN and/or LAN connectivity
Processor, memory and storage
700 MHz quad-core processor, 512 MB RAM and 4 GB flash storage
Network security and services
WPA2 encryption, Family Profiles, cloud connectivity: TLS v1.2+, DHCP, IPv6, NAT, VPN passthrough, UPnP, port forwarding and static IP
Smart home connectivity
Bluetooth Low Energy 5.0
Required for setup
Supported iOS or Android device and internet service (with cable or DSL modem, if required). See eero.com/requirements
Electrical rating
100–240 V AC, 50/60 Hz
Temperature rating
Operating: 0˚C–35˚C
Storage: -25˚C–60˚C
Operating humidity: 20%–90%, non–condensing
Operating altitude: <3000m
Dimensions
98 mm x 98 mm x 60 mm
Actual size may vary by manufacturing process.
Each certified refurbished eero router is refurbished, tested, and certified to look and work like new and comes with the same limited warranty as a new device. Certified Refurbished Amazon devices may be packaged in generic Amazon-branded boxes.
eero Pro
Device Name: eero Pro
Model: B010001
Wi-Fi connectivity
Tri-band Wi-Fi radios, simultaneous 2.4 GHz, 5.2 GHz, and 5.8 GHz wireless, 2x2 MU-MIMO, beamforming, IEEE 802.11a/b/g/n/ac
Wired connectivity
Two auto-sensing gigabit ports for WAN and/or LAN connectivity
Processor, memory and storage
Quad-core 700 MHz processor, 512 MB RAM and 4 GB flash storage
Network security and services
WPA2 encryption, Family Profiles, cloud connectivity: TLS v1.2+, DHCP, IPv6, NAT, VPN passthrough, UPnP, port forwarding and static IP
Smart home connectivity
Bluetooth Low Energy 5.0
Required for setup
Supported iOS or Android device and internet service (with cable or DSL modem, if required). See eero.com/requirements
Electrical rating
100–240V AC, 50/60 Hz
Temperature rating
Operating: 0°C–35˚C
Storage: -25°C–60°C
Operating humidity: 20%–90%, non-condensing
Operating altitude: <3000m
Dimensions
121 mm x 121 mm x 32 mm
Actual size may vary by manufacturing process.
eero Beacon
Device name: eero Beacon
Model: D010101
Wi-Fi connectivity
Dual-band Wi-Fi radios, simultaneous 2.4 GHz and 5 GHz, 2x2 MU-MIMO, beamforming, IEEE 802.11a/b/g/n/ac
Processor, memory and storage
Quad-core 700 MHz processor, 512 MB RAM and 4 GB flash storage
Network security and services
WPA3, WPA2, profiles, cloud connectivity: TLS v1.2+, AES, SHA-256, RSA and IPv6
Smart home connectivity
Bluetooth Low Energy 4.2
Required for setup
eero router, supported iOS or Android device and internet service (with cable or DSL modem, if required). See eero.com/requirements
Electrical rating
100–240V AC, 50/60 Hz
Temperature rating
Operating: 0˚C–35˚C
Storage: -25˚C–60˚C
Operating humidity: 20%–90%, non–condensing
Operating altitude: <3000m
Dimensions
212 mm x 74 mm x 31 mm
Actual size may vary by manufacturing process.
eero 6
Device name: eero 6
Model: N010001
Wi-Fi connectivity
Wi-Fi 6 Dual-band concurrent 2:2 (802.11 ax), compatible with older Wi-Fi standards
Wired connectivity
Two auto-sensing gigabit ports for WAN and/or LAN connectivity
Processor, memory and storage
Quad-core 1.2 GHz processor, 512 MB RAM and 4 GB flash storage
Network security and services
WPA3, WPA2, profiles, cloud connectivity: TLS v1.2+, AES, SHA-256, RSA, DHCP, IPv6, NAT, VPN passthrough, UPnP, port forwarding and static IP
Smart home connectivity
802.15.4 radio (Zigbee, Thread)
Bluetooth Low Energy 5.0
Required for setup
Supported iOS or Android device and internet service (with cable or DSL modem, if required). See eero.com/requirements
Electrical rating
100–240V AC, 50/60 Hz
Temperature rating
Operating: 0˚C–40˚C
Storage: -25˚C–60˚C
Operating humidity: 0%–90%, non-condensing
Operating altitude: <3000m
Dimensions
99.4 mm x 97 mm x 61.4 mm
Actual size may vary by manufacturing process.
eero Pro 6
Device name: eero Pro 6
Model: K010001
Wi-Fi connectivity
Wi-Fi 6 Tri-band concurrent 2:2:4 (802.11 ax), compatible with older Wi-Fi standards
Wired connectivity
Two auto-sensing gigabit ports for WAN and/or LAN connectivity
Processor, memory and storage
Quad-core 1.6 GHz processor, 1 GB RAM and 4 GB flash storage
Network security and services
WPA3, WPA2, profiles, cloud connectivity: TLS v1.2+, AES, SHA-256, RSA, DHCP, IPv6, NAT, VPN passthrough, UPnP, port forwarding and static IP
Smart home connectivity
802.15.4 radio (Zigbee, Thread)
Bluetooth Low Energy 5.0
Required for setup
Supported iOS or Android device and internet service (with cable or DSL modem, if required). See eero.com/requirements
Electrical rating
100–240V AC, 50/60 Hz
Temperature rating
Operating: 0˚C–40˚C
Storage: -25˚C–60˚C
Operating humidity: 0%–90%, non-condensing
Operating altitude: <3000m
Dimensions
139 mm x 139 mm x 52.6 mm
Actual size may vary by manufacturing process.
eero 6 extender
Device name: eero 6 extender
Model: Q010001
Wi-Fi connectivity
Wi-Fi 6 Dual-band concurrent 2:2 (802.11ax), compatible with older Wi-Fi standards
Processor, memory and storage
Quad-core 1.2 GHz processor, 512 MB RAM and 4 GB flash storage
Network security and services
WPA3, WPA2, profiles, cloud connectivity: TLS v1.2+, AES, SHA-256, RSA, DHCP, IPv6, NAT, VPN passthrough, UPnP, port forwarding and static IP
Required for setup
eero router, supported iOS or Android device and internet service (with cable or DSL modem, if required). See eero.com/requirements
Electrical rating
100–240V AC, 50/60 Hz
Temperature rating
Operating: 0˚C–40˚C
Storage: -25˚C–60˚C
Operating humidity: 0%–90%, non-condensing
Operating altitude: <3000m
Dimensions
99.4 mm x 97 mm x 61.4 mm
Actual size may vary by manufacturing process.
eero Pro 6E
Device name: eero Pro 6E
Model: S010001
Wifi connectivity
Wi-Fi 6E Tri-band concurrent 2:2:2 (802.11ax) with support for 160 MHz channels in 5 GHz and 6 GHz, compatible with older wifi standards
Wired connectivity
One auto-sensing 2.5 GbE and one auto-sensing Gigabit Ethernet port for WAN and/or LAN connectivity
Processor, memory and storage
1 GHz dual-core processor, 1 GB RAM, 4 GB flash storage
Network security and services
Profiles, WPA3 (eero Labs feature), WPA2, TLS v1.2+, VPN passthrough, IPv6, NAT, UPnP, port forwarding, DHCP, static IP, and cloud connectivity.
Smart home connectivity
802.15.4 radio (Zigbee, Thread)
Bluetooth Low Energy 5.0
Required for setup
Internet service (with a cable, fibre, or DSL modem, if required) and a supported iOS or Android device. See eero.com/requirements
Electrical rating
100–240V AC, 50/60 Hz
Temperature rating
Operating: 0˚C–40˚C
Storage: -25˚C–60˚C
Operating humidity: 0%–90%, non–condensing
Operating altitude: <3000 m
Dimensions
139 mm x 139 mm x 55.23 mm
Actual size may vary by manufacturing process.
eero 6+
Device name: eero 6+
Model: R010001
Wifi connectivity
Wi-Fi 6 Dual-band concurrent 2:2 (802.11ax) with 160 Mhz channels in 5 GHz, compatible with older wifi standards
Wired connectivity
Two auto-sensing gigabit ports for WAN and/or LAN connectivity
Processor, memory and storage
Dual-core processor, 1 GHz, 512 MB RAM, 4 GB flash storage
Network security and services
Profiles, WPA3 (eero Labs feature), WPA2, TLS v1.2+, VPN passthrough, IPv6, NAT, UPnP, port forwarding, DHCP, static IP, and cloud connectivity.
Smart home connectivity
802.15.4 radio (Zigbee, Thread)
Bluetooth Low Energy 5.0
Required for setup
Internet service (with a cable, fibre, or DSL modem, if required) and a supported iOS or Android device. See eero.com/requirements
Electrical rating
100–240V AC, 50/60 Hz
Temperature rating
Operating: 0˚C–40˚C
Storage: -25˚C–60˚C
Operating humidity: 0%–90%, non–condensing
Operating altitude: <3000 m
Dimensions
99.4 mm x 97 mm x 65.9 mm
Actual size may vary by manufacturing process.
eero PoE 6
Device name: eero PoE 6
Model: T010001
Wifi connectivity
Wi-Fi 6 Dual-band concurrent 2:2 (802.11ax) with 160 Mhz channels in 5 GHz, compatible with older wifi standards
Wired connectivity
One auto-sensing 2.5 GbE and one auto-sensing Gigabit Ethernet port for WAN and/or LAN connectivity
Processor, memory and storage
1 GHz dual-core processor, 512 MB RAM, and 4 GB flash storage
Network security and services
Profiles, WPA3 (eero Labs feature), WPA2, TLS v1.2+, VPN passthrough, IPv6, NAT, UPnP, port forwarding, DHCP, static IP, and cloud connectivity.
Smart home connectivity
802.15.4 radio (Zigbee, Thread)
Bluetooth Low Energy 5.0
Required for setup
Internet connection, modem, Ethernet cable, and smartphone. eero PoE 6 is powered via Standard 802.3af PoE or 15W external power supply unit (sold separately). See eero.com/requirements
Electrical rating
100–240V AC, 50/60 Hz or PoE (802.3af)
Temperature rating
Operating: 32°F–104°F (0˚C-40˚C)
Storage: -13°F–140°F (-25˚C-60˚C)
Operating humidity: 0%-90%, non-condensing
Operating altitude: <9800 feet (<3000m)
Dimensions
6.45 x 6.45 x 1.7 inches (163.8 x 163.8 x 43mm)
Actual size may vary by manufacturing process.
eero Max 7
Device name: eero PoE 6
Model: V010001
Wifi connectivity
Wi-Fi 7 Tri-band concurrent 2:4:4 (802.11a/b/g/n/ac/ax/be) with support for 240 MHz channels in 5 GHz and 320 MHz channels in 6 GHz, compatible with older Wi-Fi standards
Wired connectivity
Two auto-sensing 10 GbE ports and two auto-sensing 2.5 GbE ports
Processor, memory and storage
Quad-core A73 processor, 2GB RAM, 4GB flash storage
Network security and services
Profiles, WPA3 (eero Labs feature), WPA2, TLS v1.2+, VPN passthrough, IPv6, NAT, UPnP, port forwarding, DHCP, static IP, and cloud connectivity.
Smart home connectivity
802.15.4 radio (Zigbee, Thread)
Bluetooth Low Energy 5.0
Required for setup
Internet connection, modem, Ethernet cable, and smartphone.
See eero.com/requirements
Electrical rating
100-240V AC, 50/60Hz
Temperature rating
Operating: 32°F–104°F (0˚C-40˚C)
Storage: -13°F–140°F (-25˚C-60˚C)
Operating humidity: 0%-90%, non-condensing
Operating altitude: <9800 feet (<3000m)
Dimensions
7.24 x 8.73 x 3.54 inches
(183.9 x 221.9 x 89.9 mm)
Actual size may vary by manufacturing process.
eero Pro and eero Pro 6
Power Consumption, Low Power Mode, and Wi-Fi Off
Overview
eero Pro (B010001) / eero Pro 6 (K010001) automatically enter a Networked Standby Mode after 15 minutes of inactivity and also provides users the option to enter a Low Power Mode and disable Wi-Fi radios. The table below provides power consumption data for each mode along with simple instructions for entering each mode.
eero Pro and eero Pro 6 Power Consumption
Mode | Power Consumption (in Watts) |
Low Power Mode (Another Condition Meeting Standby Mode Limit) | 0.43 |
Networked Standby (Wi-Fi Disabled, Ethernet active) | 3.4 |
Networked Standby (Wi-Fi Enabled, Ethernet active) | 5.76 |
To enter the Low Power Mode, tap the reset button on the back of the unit 10 times (10 presses).
To deactivate Wi-Fi, tap the reset button on the back of the unit 8 times (8 presses).
Automatically enters Networked Standby after approximately 15 minutes of inactivity (no user interaction).
Entering Low Power Mode
Low power standby mode (off mode) can be enabled with the following procedure:
After the device is fully setup and on, tap the reset button on the back of the unit 10 times (10 presses)
Device will immediately enter low power standby mode and LED indicator will turn off
Device is now in the low power standby mode
To return to normal Wi-Fi mode, power cycle the device by unplugging the device from the power connector or at the wall
Deactivating Wi-Fi
Networked standby mode, where Wi-Fi is disabled but wired ethernet is still active, can be enabled in the following way:
After the device is fully setup and on, tap the reset button on the back of the unit 8 times (8 presses)
Device will reboot (indicated by a flashing white LED indicator)
Device is now in the “Wi-Fi off” networked standby mode
To return to normal Wi-Fi mode, power cycle the device through the reset button or by unplugging the device from the power connector or at the wall